Bicycle maintenance guide: How to true your wheels - News aa

Search News

Results: 1-10 of 128


International training & accreditation scheme for bicycle technicians launches revamped entry level course.

2 Nov 2023

Cytech, the internationally recognised training and accreditation scheme for bicycle technicians, has relaunched its Cytech theory one online learning course delivering an introduction to... Read more…

Canadian Cytech Training Partner visiting Scotland to advise on careers in adventure tourism

15 Sep 2023

The team from Whistler Adventure School (WAS), which recently became the only centre in Canada accredited to offer Cytech technical three, is to deliver a series of free sessions in Scotland,... Read more…

Cytech trainer back to training after providing mechanical support at UCI World Championships

24 Aug 2023

Cytech training provider Spokes People were recently asked by the Afghan National Team if they could suggest any way for them to be supported mechanically at the UCI World Championships in... Read more…

Giant Collaborate with ACT and Activate Cycle Academy to offer Giant specific Cytech e-bike qualification

16 Jun 2023

Giant UK have partnered with Activate Cycle Academy and the Association of Cycle Traders (ACT) to provide a Cytech Technical e-Bike qualification
Read more…

Cytech training provider Spokes People to deliver workshops at National Cycling Show 2023, opening this Saturday 17th June

14 Jun 2023

Lee & Darren from Spokes People, one of Cytech’s UK training providers, are attending the National Cycling Show this weekend and will be delivering various workshops and sessions for... Read more…

Retail workers face money challenges at alarming rate

31 May 2023

A report published by financial institution Claro Money’s wellbeing division on the effects of money worries for retail workers found that 73% of retail workers feel negatively about their... Read more…

Nominations open for British Business Awards 2023

9 May 2023

Nominations have opened for the 2023 British Business Awards.
Read more…

Cycle Show 2023 opens tomorrow in London - come and visit the Cytech stand over the weekend

20 Apr 2023

Cytech will be exhibiting at the show on all days on stand G670
Read more…

Cytech to deliver seminars at Cycle Show 2023, opening this Friday 21st April

17 Apr 2023

Cytech are attending the Cycle Show and will be demonstrating key practices in bike maintenance that are useful for both the trade and public.
Read more…

Just over a week to go until The Cycle Show 2023, celebrating 20 years

12 Apr 2023

Cytech, the internationally recognised training and accreditation scheme for bicycle technicians, will be joined by training providers Activate Cycle Academy and Spokes People when the... Read more…

Back to news menu

Bicycle maintenance guide: How to true your wheels

Posted on in Cycles News

You can only get the best from your bike if the wheels are straight and round.

A wobbly wheel can vastly reduce the efficiency of your bike, as well as being pretty annoying (especially if the pads are rubbing on the rim!). In order to make a wheel straight and round again, you will need to 'true' the wheel.

In a professional workshop there are many tools available to assist in wheel truing, such as a truing stand, assorted spoke keys, tension meters and dishing tools. However, the cost of buying all of these tools adds up quickly!

Pete, one of the original pioneers of Cytech training and a trainer/assessor at pjcsonline.co.uk (PJCS), is here to help with wheel truing for the home mechanic.

Preparation

Home repair is only suitable for small adjustments-for example, if spokes have come loose or for minor damage-if your wheel is more than a little bent or buckled, e.g. it's been involved in a crash or twisted in a tramline, then repair is unlikely and replacement is recommended. If you're unsure you should seek advice from your nearest Cytech certified mechanic.

You don't need to break the bank in order to be able to true your wheel at home-you can achieve a reasonably true wheel using the correct sized spoke key and a couple of cable ties. A four sided 'grip' style spoke key is best for used wheels as they're less likely to damage spoke nipples.

A wheel can be out of true in two ways: laterally (side to side) and radially (up and down). Truing a wheel laterally requires just a spoke key, although cable ties can be used. Truing a wheel radially will require both. Before truing a wheel it is normally best to remove the tyre and tube, before placing the wheel in a front fork or rear triangle (depending if it's a front or rear wheel respectively).

Truing the wheel laterally

1. Spin the wheel whilst holding the spoke key as close as possible to the rim on one side, using the frame/fork to steady your hand. While the wheel is still spinning move it closer until it clips any part of the rim-this will be where the wheel is 'damaged'.









2. Rotate this part of the wheel towards yourself, and tighten (quarter turn clockwise from your view point) the nearest spoke nipple on the opposite side to where your key clipped the rim.

Note: The 'side' that a spoke nipple is for can be worked out by following the spoke down to the hub, and are alternate in the majority of cases. From your view point if the spoke is connected to the left of the hub, then tightening it brings the wheel to the left, and tightening a spoke from the right of the hub brings the wheel to the right.

If this nipple won't shift, you could try loosening (quarter turn anti-clockwise) the two nipples either side of the one that you wanted to tighten.


3. Spin the wheel again, moving the spoke key closer until it touches again. Repeat the above process two or three times on the first side, and then do it again on the opposite side. This process will slowly bring the wheel towards the centre of the fork/rear triangle.

Truing the wheel radially

Now the wheel's reasonably straight, we can start on making sure it's round.

1. Fit the cable ties on the fork/rear seat stays and swing them in above the rim surface. Move them down while spinning the wheel until they just clip any part of the circumference of the rim-this is where there's a 'bump'.

If spoke tension is low overall then we can 'pull in' the rim where it touches the ties. This is the easier option.








2. Starting with the spoke nearest the centre of the found 'bump';

i. tighten this spoke ¾ turn clockwise from your perspective;
ii. tighten the two spokes either side of the first spoke ½ turn clockwise;
iii. tighten the next spokes outwards ¼ turn clockwise.

Spin the wheel and move the cable ties down to just clip the rim again, and repeat the previous process as many times as necessary to get the wheel radially true.

If spoke tension is high overall, concentrate on the spokes where the gap(s) appear between the rim and the cable ties, again working from the centre outwards as per step 2, but this time loosening the spokes (turning anti-clockwise).

3. Next, re-check the lateral trueness as per first process and fine tune.

Before re-fitting the tyre and tube you need to pre-stress the wheel on both sides.

4. Place the wheel (axle) on a block of wood or similar object on a low table (or the floor if safe to do so). Hold the wheel on both sides of the rim, one close to the valve position and one near the join (normally opposite the valve), and just lean forward putting your weight on the rim. Move round about 1/8th of a turn at a time and repeat, until you've completed at least one revolution, then repeat on the other side. During this process, you will normally hear creaking or cracking noises from the wheel-this is just the spokes settling in. The wheel may require a further truing process to fine tune the finished product once you've pre-stressed it.







Pete's top tip: If you're not sure which way to turn the spoke key, then I use my left hand to tighten clockwise, and right hand to slacken spokes, pushing my thumb over the spoke nipple being adjusted with the spoke being closest to me.

Wheel truing isn't something that can be rushed; patience and minor adjustments are key. Some people even find this process therapeutic, and a good end result is satisfying in anyone's books. If you want to learn more about the art (and science!) of wheel building make sure to check out the wheel building courses offered by Cytech!

Article by Pete (Cytech master technician)

Back to news menu

Useful links

If you have any other queries please contact us.

The Cycling Experts is brought to you by the Association of Cycle Traders.